liquid temperature control equipment.
Superior Engineering Co. , Ltd. Offers fluid-
Cycle equipment for molding, extrusion and Thermoforming: coolers in portable and factory-wide central systems.
Portable chillers range from 1-to 30-
Tons cooling capacity in airand water-
Concentrated design.
The central chiller is in 10-500 tons of air-and water-
Concentration of outdoor and indoor systems. Mold-
Temperature Controller in wateror oil-
Loop system.
The water unit operates between 30f and 250 F;
Oil unit between 100 F and 500 F
Cooling tower system from 20-to 1000-ton capacity.
Metal and fiberglass tower cells are provided.
Relevant pumping equipment can be customizeddesigned. Open-and closed-
The loop design is standard.
Engineering services including central cooling systems.
It can be a computer device.
Used for remote control and information collection and storage in molded batteries or factory systems.
Water/application engineering offers a standard Water temperature range-
Control unit with 3/4-to 10-
Hp pump and standard heater selection from 9 to 24 kw with stain-less-
Steel sleeve structure.
The device has an easy-to-control microprocessorto-read LED, dual-
Temperature display of setting point and process temperature;
Optional SPI communication protocol for CIM and SPC applications; and full-
A graphical display panel with display operator status and alarm indicator light.
Packed at a low
Profile cabinet designed for stacking and easy maintenance.
Standard options include negative/positive-
System water-pressure unit
Clear and close-
For high-
Temperature Heat-
Deliver liquid or hard liquidwater areas. TDW-
M True Temp series covers a small area and can be repaired
Sheet cabinet design with hinge electrical panel and operation interface.
9-compact designand 12-kw direct-
Water injection device including site
Verified NX series microprocessor control with graphics panel and simple-to-read display.
\"Crash cooling\" function standard for accelerated cooling.
The optional electric regulating valve provides high accuracy at different loads, helping to reduce water strikes. TDH series hot-
Oil unit design for high temperature heating and cooling applications from 100 F to 550 FSelf-
The included units provide an optional \"U\" type heat exchanger that can withstand thermal shock.
Standard Microprocessor temperature control accurate to 1 [degree]F.
Portable air production lines have also been establishedand water-
1 to 40 HP cooling chiller;
And the central system is in the air. and water-
Cooling configuration from 15 tons to 155 tons. On 15-
Hp units and larger Discus compressors are the standard to help optimize energy efficiency.
Direct-new DDW series
Drive the central chiller with a rated model of 42 to 159 tons
Drive an open compressor coupled with an industrial motor. Units use 15-
Compared to chillers with half load, the energy under 20% load is reduced by 100%
Sealed compressor. Space-saving Porta-
Small Kool II cooler range in air-and water-
Cooling models from 2 tons to 10 tons.
Architectural features include usable cabinet design, 30-
Gal non-corrosive polyethylene storage tanks and non-ferrous metal pipes.
The standard NX series microprocessor control is accurate 【+ or -]1[degree]
F dual LED display with set point and power supply temperature.
Condenser and forming machine hydraulic cooling tower system forced into polymer Tower-
Induction of ventilation and fiberglass
Draft models from 30 tons to 200 tons. AFFINITY INC.
Compact and high manufacturingcooling-
Capacity cooler with standard remote control. F-
The series has achieved from 10,000 to 170,600 Btu/hr [+ or -]1[degree]
F stability and unlimited access to all components, thus reducing service time.
Features include colored coolant loops, Noneflow and low-
Liquid Level Alarm, hot-
Gas bypass with long, high/low compressor life
Temperature alarm, high
Capacity heat exchanger for high heat
Transmission efficiency.
Digital reading (C or F)
The microprocessor is fully programmable for functions such as slopes. to-
Set value to prevent thermal shock.
Because F-saves floor space
The series is usually 30% smaller than other chillers.
Alpha equipment
The product line includes: * portable chillers with 2 to 40 hp, water and air condensate equipment.
* Central chiller system with 20 to 120 hp, water and air concentrate.
* Wet/air removal-
Adjustment system for factory or molding-
Room applications, water and air concentrates of 10 to 60 hp. * Cooling-
The tower system is designed from 4 tons to 1200 tons. * Cooling-
Tower cells in fiberglass
Reinforced polyester from 7 tons to 1000 tons.
Galvanized from 6 tons to 1000 tons. * Water-
Filtration system for cooling
Frozen water and alcoholwater system.
* Automatic water-
Processing system working with cooling-tower system.
* Open liquid temperature controllerand closed-
Circuit system, singleand dual-zone units.
Alpine industriesWater-
The Chilling system includes: * industrial opening-
Drive chiller using compressor to eliminate motor burn
Expensive cleaning
Ups or extended down-time; energy-
Efficiency ratio (EER)of 16 or more; built-
Capacity control in response to suction pressure;
Reduce positive uninstall start of input
Urgent demandExtra-
Quiet models and explosions
Proof options are provided.
* AMA portable air model
Cooling chillers assembled on strong steel racks and heavy-duty-
Duty casters for moving. Features high-
Sealing or semi-sealing efficiency
Fully enclosed compressor, fully insulated cooler, air-
Cooling condenser, insulated water tank, process pump, solid-
State temperature controller with built-in readingin freeze-
Statistics, function lights, pressure gauges and operation and safety control.
Custom options include12 or explosion
Automatic alarm system, automatic alarm system
Gas bypass, capacity control or energy-saver, two-
Speed regulator, Double Pump, heat recovery, low ethylene glycol
Temperature unit, frozen-
Water flow switch.
* AMW portable water model
The cold chiller is similar in structure to the AMA model, water-
Not air cooling-
Cooling the condenser.
Complete units are available for all model AMA standard and optional features.
AMCOT cooling tower Co. , Ltd.
Low traffic and cross traffic
Noise cooling tower and a high
Temperature cooling tower of 212 F.
Unit includes an induction
The axial flow fan installed at the top of the tower is used to suck out the air flow counter current design.
Low internal pressure loss and bottle-
Shape Design is reported to ensure optimal efficiency and space economy.
Shell by non
Rusty fiberglass
Reinforced Polyester (FRP), a high-structural-
Strength material that helps to prevent impact damage and cracking.
The filling material is honeycomb heat-
Formed embossed PVC allows high heat transfer for optimal efficiency and maximum airto-water contact.
American Jet CorporationOffers beside-the-press, closed-
Automatic chiller for 12,000 to 240,000 Btu/hr.
Anti-use of RF cooler
A frozen mixture of water and ethylene glycol.
See AEC/Application Engineering for application engineering.
Water supply for application process equipmentCold, water-cooling, water-
Recycling and water-
Filter system.
Portable, Central and hot-included-
Water pump chiller in wateror air-Cool version.
Central Cooling-
Both open and closed systems have tower systems.
Closed system available for boardand-
Frame stainless steel heat exchanger.
All systems are equipped with complete engineering drawings for economical local installation, guaranteeing a full year in terms of parts and labor. AQUATEMP INC. Builds chilled-
Air-water systemand water-
Cooling chillers from 1 unit.
5 to 300 tons, water tower, sand filter, water pump, etc.
Baltimore Airlines
Provides evaporation cooling equipment, including cooling towers with cross flow and counter flow configuration, factory-
Assembled into a modular unit of 2110 tons/32 million Btu/hr and on-site-
Erect Tower to 25,000 gpm/cell;
And steam condenser, industrial fluid cooler, heat exchanger and heat-storage units. Factory-
Assembly equipment available in heat
Galvanized steel sheet with fiber
Glass or stainless steel. Field-
Erect model built with wood, steel, concrete or pull-up structural composites.
Plate Heat Exchanger-and-Frame and shell-and-
Tube configuration.
Berg cooling systems
Cooling equipment includes half
Seal, open drive or screw compressor controlled by microprocessor; air-
Cooling Device with heat recovery; water-
Cooling device with \"free cooling; clean-
Water tower system; pre-
An encapsulated mezzanine system;
Portable chillerblown-film coolers; temperature-control units; mold-
Area dehumidifier; chemical-
Treatment Package; and water-
Filter system.
Non-corrosive fiberglass tower with low
Hp motor and construction-steel bases.
Buza Industrial Co. , Ltd.
Chiller production line, hot-water and hot-oil mold-
Temperature controllers, cooling towers and pumps-tank sets.
The Ice series of chillers covers a variety of styles, featuring Selfcontained, mid-
Size units with refrigeration and waterway pipes and cables from 13 to 35 tons. The 7-and 10-ton air-
The cooling pipe line of the portable chiller uses a blower instead of a prop fan to pass the air through the condenser coil, allowing the use of a pipe to control the heated air flow of the outlet unit.
Ranging from 3 tons to 15 tons, there are units in both airand water-
Cooling configuration.
Double central chiller
Refrigeration circuit, easy to repair electrical appliances, full
Unit framework for component protection.
The cooling tower has a standard galvanized and FRP configuration of 5 to 175 tons, as well as a larger size and multiple configurations. Pump-
Water tank assembly adjusted size according to flow requirements of each cooler or cooling tower, characteristic water tank cover, pre-
Wired electrical housing and alarms, as well as spare pumps and custom configurations.
Cooling tower with capacity from 20 tons to 200 tons.
The design includes three different temperature control methods to achieve a more accurate process
Water temperature.
Tower with pump
Tank groups that provide maximum cycle and temperature control. Mold-
Single temperature controller
Multi-zone configuration with temperature control to 250 degrees Fahrenheit
Low unit functionwatt-
Density heater and microprocessor
Based on the temperature controller.
BTU products cover a variety of water and oil temperature controllers with temperatures up to 650 F.
Can be singleor multiple-
Regional configuration and direct-
Injection and closure
Loop arrangement.
Edwin L. WIEGAND DIV.
Portable mold available
Temperature control system in a compact 15x24x25. package.
Water is provided at temperature, from level 4 to level 250 F.
5 to 24kw, open-or closed-
Cycle the pipe according to the mineral content of the water.
For injection molding and other plastic applications, the WTCS system integrates 3/4-
Hp centrifugal pump with flow rate of 30 gpm.
In order to obtain the maximum reliability, the system has automatic deflating and low
Pressure Switch, over
Pressure-temperature protection
Easy-to-operate safety valve and microprocessor controlto-
Read digital display and high/low-
Temperature alarm.
Mira clone Cincinnati, USAS.
Plastic Machinery Division
Portable chillers range from 1-to 30-
Tons, solid-
Status or microprocessorbased controls.
Water supply for central chiller and central chiller modules-
Cooling capacity of water from 5 to 180 tons
Cooling configuration and air-
Cooling capacity of 5 to 30 tons.
Can assemble 175 tons of evaporation cooling tower battery;
There are bigger units. Pump-
Basic or complete tank set
Functional design with diagnostic and standby pump with battery.
The ATC series is a closed combination
System unit with 30-60 F cold-
Water, electricity and hot water-
Water circuit on 250 floorMold-
The temperature controller for water and oil ranges from 15 to 100 gpm.
Solid for water unit to close or turn on cooling
Status or microprocessorbased controls.
The oil unit includes microprocessor control and can provide an optional cooling loop.
Connell TEMPRO Group Ltd. Water-
The temperature controller in the Thermolator series offers a variety of control complexities and unique dual
Eliminate casting of up to 40 leaking workpieces-
Easy bending accessories for conventional controllers.
Model with temtrac solid
State control is singlezone, direct-
Injection Device with pump size 0. 75 to 7.
5 hp, 9 to 24 kW.
Month Thermolators single with mcchke and mcchke month microprocessor controlor dual-zone, direct-
Injection model of 9-to 24-
Kw heating, single-or dual-zone, closed-
Circuit model with 9-or 12-kw heating.
Higher kw heating available when offcircuit models.
The size range of the pump is from 0. 75 to 7. 5 hp. Ultra-
The standard performance pump on MicroTrac 3 is an optional product for all hot thermol.
In order to improve the cooling capacity, it can improve the performance of the pump by 50%. Forty-
Two microKool portable chiller models are available from 3.
25 to 40 hp in the airand water-
Cooling design with two Microprocessor controllers to choose from.
The product line includes 1 micro chiller.
5 to 5 hp in the airor water-
Cooling configuration.
Central Chiller includes outdoor air conditioning
Cooling package of 20-to 150-
Capacity per ton, dual-and multiple-
Compressor design. Indoor water-
The cooling central unit from 10 tons to 120 tons has a single compressor or a double compressor.
MicroTrac 3 control is standard, Copeland is also standard, half
Seal, iron cake compressor. Pump-
The tank components of the central system include 180-to 1100-gal roto-
Molded PE cans or epoxy
Steel reservoir lined with steel or stainless steel, from 400 to 4000 gal. Pumps from 1.
5 to 100 hp can be customized according to system requirements.
The capacity of the cooling tower is 10 tons to 500 tons or more. Heavy-
Multimedia bypass filters are provided.
Cooling Technology Co. , Ltd. Offers air-and water-
Temperature-cooling chiller
Control Unit and cooling tower system.
Including Mini-Portable (1 to 10 tons), Portable (5 to 40 tons)
Multi-loop (20 to 140 tons)and Direct-Drive (30 to 200 tons). Cooling-
The tower system ranges from 10 tons to 500 tons and can provide metal or fiberglass tower batteries. Temperature-
The size of the control unit from 3/4 to 15 hp.
The company has developed a cooler dedicated to extrusion applications, and there is a patent pending on the direct Freon injection unit, which is designed to shorten the hard-to-cool molds.
Delta Cooling Tower Limited
Polyethylene non-corrosive cooling tower is provided.
Pioneer cooling tower and Paragon induction-
Ventilation cooling tower for industrial use
Grade materials with low maintenance costs during the service life of the equipment.
The unit is modular, pre-
Simple, fast and economical installation, plus easy to upgrade in the future, with light assembly and weight.
Integrated device package with automatic process control fully pre-assembled, pre-wired, pre-piped and skid-
Install if needed.
Delta T Systems Ltd. Offers water-and oil-
Cycle temperature-
Single control equipmentand multiple-
Regional structure, direct injection or closed circuit, compact and upright style.
Options for controllers and options include RS232, RS422, RS485, SPI protocol, special alarm, electrical, JIC, Redwood, explosion-proof, etc. Hot-
Oil system available for single 650 Fand dual-
The area structure of the heater size from 12 to 300.
The flow range is from 10 gpm to 300 gpm, using positive-
Displacement pump.
Edwards Engineering
30 types of liquid chillers are available from 1/2 tons to 240 tons. Air-Cooling or water-
Large stainless steel cooling unit
Steel reservoir, and walking-in weather-
Anti-equipment Housing, automatic capacity control from 0-
Double 100%-
Arrangement and damage of the pump-
If the cooler is frozen inside, the evaporator design is resistant. Low-temperature (to -100 F)
There are also units.
Other features include automatic air removal, automatic head-
Outdoor air pressure control-
Cooling model, single central control panel, multiple indicator meters, closed water system, internal or external installation and portable equipment with casters.
GC industrial company
Portable chiller durable, compact and self containedcontained. Units are air-and water-cooled in 0.
5 to 50 tons and provide coolant in the range of 20f to 65f
Semi-closed
Seal design is provided.
Power supply for equipment-saving hot-
Gas bypass system without corrosion stainsless-
Stainless steel and copper heat exchanger
Steel pump and tank. Air-
The condensate unit has a full-size condenser to maintain the capacity in a high temperature environment. Water-
Condensation Model has water-
Saving automatic regulating valve. Special low-
Temperature cooler has the following temperature capacity40 F.
Central chiller
Including or splitting system installed inside or outside, air-and water-
From 5 tons to 400 tons.
Cooling tower size 6 to 500 tons.
The water tank and pump set of the central chiller and cooling tower are custom designed.
Hamilton AVTECOffers direct-or indirect-cooling liquid-
Temperature Controller, pump size from 1/2 to 3 hp, 3-12 kw heating.
Strong control package-
State of control or microprocessor.
Portable air Series 2000or water-
Cooling chiller with size 2-to 35-
Tons of refrigeration capacity includes:
Rated parts, solid-
Half-State temperature controller
Sealing compressor and heat-gas bypass. Also process-
Water system including central chiller, water pump tank and cooling tower. Heat-
The recovery system can be used to recover process heat and use it in winter to replenish plant heat. IMS CO.
Provide a circulator for the mold
Temperature control. All have easy-to-
Read the meter and make simple service access to all components. Closed-circuit Water-
Hot Selling stars and Temkon SS
Stainless steel for water circulationsteel tanks. Water-
The Star unit has four cooling options, including
Contains air cooling. HV65 hot-
The characteristic of the Water circulator is rust
Stainless steel resistant
Steel and copper pipes for direct cooling;
Proportional controller; and high-and low-
Pressure Protection.
Units available for vertical or horizontal use. Model 6 oil-
The maximum temperature of the heating circulator is 400 F; Model 8,550 F. Air-
1/2-cooling chiller, 1-, 3-and 5-
The ton size is portable, requires minimal maintenance and is self-containedcontained.
Other sizes made to order.
Industrial energy saving Co. , Ltd. Offers serf-contained air-and water-
Cooling chillers of 1/2 to 500 tons.
Optional equipment includes pumps, tanks and special materials. Industrial-
Quality cabling is standard for optional JIC and hazardous-area wiring.
Special control and meter options are also available. KLEEN-RITE INC.
Circulating chillers using flat plates-
Heat exchanger.
On one side of the plate there is a carbon fluoride refrigerant and on the other side there is water.
It is reported that the temperature change can be done in about 5 seconds.
1-units providedto 5-
The ton capacity of the temperature from 40f to 110 F is controlled by a remote bulb thermostat or electronically.
Logic Equipment Company
Negative Productionpressure leak-
Negative/positive-pressure mold-
Temperature Controller up to 400 FVac-U-
Temp is a general.
Purpose temperature controller with negative-and positive-
Pressure mode, can be used at the same time.
In addition to controlling the temperature, it can also prevent leakage, improve the quality of the parts and shorten the cycle time.
It uses water and other heat. Conveying fluid.
The company has developed a patented process that, by transferring water through a core of any size between half parts of the mold, discharges the formed gas into the tube line and cools the long and thin core.
Free design consultation for mold exhaust and cooling is provided.
Marvel equipment
Provide heating and cooling devices for water or oil temperature control up to 655 F (
Water units to 285 F)
Used for injection molding molds, extruder, rollers, storage tanks, presses, screws and other applications. Mold-
Temperature control unit manufactured by Swiss Regloplas AG. Optional RT-
The 41 microprocessor control system and the rs23c interface make it possible to connect to the process
Control system for production installation. RT-
The 40 with a serial interface allows to store parameters to 16 different users.
Matsui United States limited
Three series of wateror oil-
Cycle mold
Temperature Controller is provided.
The MC Jet III series has digital settings and indications with set points and actual values, as well as delta-T.
It is possible to display either the inlet and return fluid temperature or the actual mold temperature.
7 alarm indicator lights, PID temperature control and automatic electronic timer
Provide startup.
Communication is optional.
Three models of motor drive from 0.
33 to 1 hp, heater capacity from 3 to 8 kw, providing fluid temperature up to 390 F
More powerful MC Jet III-
Increase the capacity of X pumps (1. 5-2. 9 hp).
The 10 models offer a heater capacity of 8 to 10 kw and can control up to 390 F.
Multi-nozzle II combined Hopper loaders, dryers and molds-
The temperature controller in a compact mobile cabinet contains one of three models of the MCII water or oil mold
Temperature Controller with 0. 33-hp motor and 3-
Kw heater capacity with fluid temperature of 320 degrees Fahrenheit
Eight MKC water-
The cooled chiller has a FRP water tank and an open-ended-
Type compressor.
The range of the pump is from 0. 5 to 2. 9 hp. MOKON DIV.
Protect closed company
Circulating water and oil temperature-
Control System with temperature range up to 600 F, portable chiller and custom designed fluid-
Processing system.
A water system with a maximum operating temperature of 300 F and a pumping capacity of 120 gpm and 60 psi can be used in the ccabinet and unccabinet series.
Non-ferrous metal structures ensure long service life and prevent corrosion.
The combined heating/cooling unit provides temperature control from 35 F to 250 F with a cooling capacity of up to 20 tons.
Oil system contains cooling-
Oil storage tank to eliminate heat shock associated with in-fine shell-and-tube heat-
Switch cooling.
Up to three separate control areas can be provided in the same cabinet, and pumping capacity up to 30 gpm and 100 psi can be provided through maxi.
Operating temperature 600 F. Air-and water-
The cooled portable chillers range from 1/2 tons to 20 tons. Corrosion-
Free construction including non-ferrous metal pipes, stainless steel pipes
Steel supply pump and evaporator, and heavy-duty-
Plastic reservoir for extended life. Solid-
State or microprocessor control standards for all systems.
Optional microprocessor control with serial communication, SPI protocol and computer interface functions.
Custom temperature control system specially produced with leakage
The main line of negative-
Designed to eliminate pressure systems for handling problems related to leakage.
Omega Engineering Limited
Provide continuous
Temperature circulating bathtubs, as well as a full range of sensors, instruments and hardware accessories for monitoring and controlling waterand oil-
Loop system.
Production of liquid chillers and constant-POLYSCIENCE-
There are a variety of cooling capacity of the temperature equipment chiller, there are a variety of pumps to choose from. Temperature-
Control devices that can be used for process applications, and for small-
Laboratory of scale and quality
Control requirements.
From basic analog control to programmable controllers, units that provide controller options can provide RS232 interfaces for complex time/temperature distributions.
Cooling and process available-water filters.
The system uses permanent filter media to remove particles as small as 5 microns.
The filter reduces the dirt of the cooling equipment and maintains the efficiency and low use of kw.
Filtration improves water quality, eliminates drainage and flushing of equipment, reduces chemical costs and prevents downtime.
Progressive Equipment Company
Provide electronic water
Can include the treatment system of electronic water treatment equipment
Bag Filter and auto blowdown valve.
The processor electronically removes dirt and dirt from the pipe without chemicals.
When electronically treated water passes through the system, the existing scale is etched, thereby increasing the cooling potential of the system, which is reported to extend the life of the equipment, reduce downtime, and improveHigh-capacity, full-
The Bag filter works with the processor.
Bag filters provide an alternative to bulky \"Y\" filters and sandand-gravel filters;
According to the company, they provide the full amount
Flow filter at reasonable cost, reduce downtime, save water, and the dean is easy to operate.
Sentinel pressure-
Drop alarm system detects pressure drop in filter media as low as 3-5 psi.
Ozone and/or UV rays used as part of non-chemical water-
Processing package when applicable.
Complete turnkey engineering, equipment and installation services are provided.
Protection cooling tower company
Provide fiberglass cooling towers from 5 tons to 1000 tons. Round bottle-
Type shape with 360 [degrees]
Air intake reduces air resistance.
Light weight, corrosion-
Free installation, long service life and low maintenance cost.
The company\'s V25 filler is made of flames
High flame retardant rigid filmheat-
Exchange efficiency.
It guarantees the uniform distribution of water and has the least resistance to the airflow.
Quality Process Control Systems
Make portable chillers and waterand oil-
Circulation device.
Customized systems are available. Air-and water-
Enclosed and semi-enclosed portable chillers of 1 to 15 tons
Sealing compressor is provided. All-
Copper, insulated pipes, insulated steel reservoirs, heat
Standard gas bypass and stainless steel/copper heat exchanger.
Compact and upright straight line, singleand multiple-zoned, water-
The loop unit can be either digital or microprocessorcontrolled.
Features include sealing flush, flange, vertical installation, lowwatt-
Density immersion heater;
Internal bypass; turbulent flow;
And hinge Access Board. Single-or multiple-zoned, high-
Oil-temperature
Digital or microprocessor for cycle units-controlled.
The centrifugal pump with sealed cooling is standard. Low-
Wattage density, flange immersion heater, hinge plate, over
Temperature safety, internal bypass, process shutdown-
Valves, pressure gauges and function lamps are standard.
See Marvel equipmentRITE-
The temp manufacturing offers a range of four designed chilled water coolers with a rated power of two to 20 tons. Both air-and water-
Cooling unit standard is 40-gal stainless-
Steel evaporator.
Other features include portable equipment, indicating instruments, indoor or outdoor installation and user-
Friendly control.
Special controls, meters, or electrical options are available. R. J.
Industrial Company.
Replacement water and hot water provided
Oil pump for Chiller, mold for most brands
Temperature controllers, cooling towers and a variety of water-Cooling system.
The pump perfectly matches brands like Scot, Burks, Aurora, Sherwood, B & G, Price and Worthington. A cross-
Reference materials for OEM pumps have been compiled to quickly identify replacement sealing kits and other components.
Models that were discontinued during the time were also crossed
Refer to the alternatives currently available.
Shi Lai Bell Co. , Ltd.
All over the air-and water-
The cooled chillers range from 1/2 tons to 20 tons and are characterized by water systems designed for unrestricted circulation and appropriate turbulence in the heat exchanger;
Eliminate the use of-freeze; extra-Large stainless steel
Steel, pollution-free Reservoir;
Taikang compressor;
Long-life polyester powder coating;
Traditional accessories, parts and motors that are easy to replace. A 7 1/2-ton, 90,000-
The Btu unit has a reclined control panel for easy operation, cycle on/off as needed, no heat-
Gas bypass and have \"pollution-
Free bronze pump. STERLCO DIV. STERLING, INC.
Make waterand oil-
Cycle temperature-control units.
Each system has its own circulating pump, thermostat and operating control.
Can be provided in the operator-
Height cabinet or low-
Compact cabinets.
Customized Engineering Systems are available.
9300/9400 series of water-
Cycle temperature-
When there is sufficient water supply pressure, the control unit covers the temperature range from the water supply temperature to up to 300 F.
Standard unit with 9-kw, low-watt-Density, copper
Sheath heaters with pumping capacity from 1/2 to 5 hp.
24 kw heater available in standard cabinet design.
Units can be manufactured in single, dual-or three-
Common electrical and water for regional construction and function-
Supply connection.
They can provide microprocessor-based or solid-
Status digital controller.
Computer included options-
Interface capability (
Serial port, RS422, RS485, SPI protocol)
Special alarm, fixture
12 construction, non-ferrous pipeline, special power requirements.
Every system has double 1000.
Ohm platinum RTD sensing probe, lowwatt-
Copper density heater
Sheath element providing thermal conductivity, halfand full-
Heating capacity, variable timing cooling (VTC)
, Specially designed \"Sterlseal\" pump seal to minimize downtime and high
Technical Controller.
3300/3400 series temperature-
The control unit provides the same functions and capabilities as the 9300/9400 series.
Advanced electrical equipment is also included
NEC compliance (
National Electrical Code)standards. High-temperature-
The control system covers a temperature of 650 degrees Fahrenheit.
The heater sizes range from 6 to 300 and the pumping capacity ranges from 10 to 600 gpm. Low-watt-
Heavy duty density heaterduty positive-
Push circulating pump
The button control and security components are standard.
In addition, a cooling function with automatic control is provided, which utilizes a specially constructed heat exchanger.
Individual units availableand dual-
Regional structure, can provide a variety of controllers. NEMA-
The structure of the 550 F system is standard. STERLCOOL DIV. STERLING, INC.
Manufacture portable chillers, as well as central chillers, cooling towers, pump tanks and water-
Install and start the auxiliary filter device.
Portable chiller in air-and water-
1-cooling modelto 30-hp.
The unit supplies frozen water from 0f to 75f under various flow and pressure, using singleand dual-pump systems.
The functions include full PID self-tuning microprocessor control; 40-
Gal insulation, whole reservoir;
Centrifugal circulating pump of 11/2 HP;
Non-ferrous metal reservoir and inner pipeline, half
15-sealed Copeland \"discus\" compressor for unitshp and larger; hot-
The gas bypass capacity control is accurate [+ or -]1[degree]F; shell-and-
Tube evaporator that can clean the shell-and-
Water pipe condenser-cooled models; and high-efficiency fin-and-
Tube Condenser in aircooled models. Air-and water-
The central cooling system is cooled to 300 tons, the cooling tower is cooled to 900 tons, and the pump, pump tank and water filtration system are provided. TEMPTEK, INC.
Manufacturing molds-
Temperature Controller, portable chiller, pump-
Tank Station and cooling-tower cells.
Fluid circulation temperature-
The product is designed for simple machinery, easy operation, use \"super\"
Solid construction, less components, standardized production.
Temperature Controller for both water and hot wateroil open-and closed-
Loop configuration.
Oil-water unit controlled to 250 F
Cycle unit up to 400 F. Small, space-
Energy efficient equipment
Process pumps, flange heaters and advanced electronic instruments with remote functions.
Portable chillers and refrigeration modules are available in the airand water-
Condensed version.
The unit ranges from 1 ton to 20 tons and the operating temperature ranges from 30 to 70 degrees Fahrenheit.
The refrigeration module ranges from 5 tons to 30 tons, and the operating temperature ranges from 20 to 60 degrees Fahrenheit. Pump-
In order to take advantage of the minimum floor area and at the same time emphasize the vertical size of the water storage, the storage tank station is designed.
Standard process connection for pumps, sensors, drains and water
Level control simplifies installation.
10 to 480 tons of energy used in cooling towers with galvanized metal or fiberglass structures
Efficient prop fan, spacious wet deck and large reservoir.
Self-Care for heat care/Maya portable coolercontained air-or water-
Cooling Design of 1/2 to 40 tons with barrier-free cabinet design, hinge control panel and double
Digital Display, 7 positive numbers
Action switch and 19 diagnostic lights. Air-
Cooling central chiller with heat
Recycling indoor equipment or low
Environmental protection outdoor unit with capacity of 200 tons. Water-
Cooling central chiller in 3 compressor configurations: 1)
TPW economy factory system of 20 to 130 tons, with half of the maintainable
A sealed compressor for precise temperature and capacity control and two or more independent refrigeration circuits; 2)TCCW energy-
Efficient Design with direct function
Compressor system driven by environmentair-
Cooling industry T-
Frame motor and capacity of 35 to 170 tons; and 3)
WN unit featuring opentype, belt-drive, slow-
Speed compressor for reliability.
The fiberglass cooling tower has two design series, from 3 tons to 850 tons, with flexibility in meeting difficult installation conditions.
High FC and FT series
Efficiency induction
The ventilation design and the strong, lightweight FRP housing can withstand corrosion.
Customize the pump/reservoir assembly of any size and configuration for tower or chiller applications.
System function 1/4in. double-
Welded steel structures, strong pump decks and pre-installed pre-wired control panels. Water-
A treatment system designed to control the growth of dirt, corrosion, suspended solids and microorganisms. Temperature-
From 1/2 to 7 1/2 hp, the full range of pumping, heating and cooling configurations for oil and water from 3 to 24 kw provides control units.
Standard features include dual tank/pump, unit cast construction, microprocessor with dual digital display, seven positive
Operating switches, 15 diagnostic lights, etc. T. U. C. INC.
Manufacturing liquid
Cycle temperature-
Control equipment including water and hot water
Oil temperature controller and portable chiller.
The water unit is upright and low
Configuration file and subcompact configuration.
The controller is a digital or microprocessorbased.
The microprocessor unit has the functions of rs23c, RS422 and RS485. Dual-
Solid probe sensing
State control and a sleeper pump with sealed Flushing make the operation of the equipment simple. Single-
And a multi-region model with optional features. Hot-
The temperature range of the oil system is from 100 F to 500 F, and the heater capacity is from 6 kw to higher.
Centrifugal pump with water
Standard cooling seals.
The unit has an upright and compact model, as well as a multi-zone configuration.
Portable cooler with airand water-
Cooling condensation of 1 to 20 tons.
Standard features include heat
Stainless steel gas bypass
Fully insulated storage tank of steel or non-ferrous metal
Copper pipes and frozen-stat control.
Van steenburgh liquid chiller
The Trak series is a reciprocating liquid chiller from 2 to 7.
5 tons of heat
Recycling capacity and the use of a patented Head Start receiver ensures immediate start-up in low ambient conditions.
Access valves for all parts of the refrigeration circuit are on the front panel for easy repair and refrigerant recovery.
Three-row chillers for West Coast plastic equipment (Schreber, Rite-Temperature and Arctic)
Especially hard for the West
Water conditions from 1 ton to more than 250 tons. Also mold-
Temperature Controller for TEW (Taiwan)in 3-and 5-
Kw rated power is reported to be up to 302 F in circulating water or oil media in a single failurefree unit.
The cooling towers are allocated by three builders: Marley\'s traditional tower, jr\'s fluid cooler and Amcot all-
Glass fiber Tower
Capacity range from 3 to 200-plus tons.